Add an Optional Adjustable Graphite Plate
that slides onto the shaft of your torch
stand.  It can rotate and adjust up and
down the shaft.  6 x 6 high density,
isostatic graphite plate.

$70.00
Hand Held Torch Stand - 32.00
  • Adjustable hand held torch stand
  • Designed to hold your hand torch
  • Can adjust from 6 to 9 inches in
    height
  • Can be customized to the height
    desired
  • For mounting on bench or lathe
Lathe Hose Holder - $30.00
  • Designed to keep your hose from
    tangling and wearing out swivels.
  • This hose holder will swivel out of
    the way to allow tube to be slid in
    and out of lathe.
  • Outer hanger is a hook, allowing
    quick disconnect of hose from tube.
FireKist Swivels
1/4" Straight - $45.00
1/4" , 90 degree - $50.00

3/8" Straight - $60.00
3/8" , 90 degree - $70.00
Blast Shield Patent Pending
These Swivels are made from Stainless Steel.  
Flawlessly Smooth , Precision Machined , Double ended.  
Clean them with soapy water.  
Thank you Seth from FireKist Glass , for allowing us to carry these for you.
Lathe Torch Stand has 6" shaft for Torch.  Bench Torch Stand has 18" shaft for
torch.   Rail to go in and out is 15" for either Lathe or Bench.

Holes are pre-drilled for your torch.  Mounting hardware NOT included.
Thank You Grateful J for your help with fitting Herbie's
Swivel is required for - Herbie's , CC w/ B&S , and
some Bethlehem.
New Swivel , just tighten and Move , Anodized
Aluminum
Blow Hose Assembly- $15.00
Only Blue
Available
10mm Boot - 4 Pack $6.00
12-13mil Boot - 4 Pack $6.00
15-16mil Boot - 4 Pack $6.00
18-19mm Boot - 4 Pack $6.00
Finalized Blow Hose
Assembly, with Blow Hose ,
Swivel and Boot.

Parts Sold Separately.
Bunson Burner Torch - $135.00
We made the middle shaft square, so the
ports always stay aligned.

Large Magnet in Bottom + 2 screw holes
provided for mounting.
Short Bunson Only Available

Small Bunson Burner - 3.75" Bottom Height

Move up to Adjust Flame, Oxegen.   You will need
to add a regulator to the lines going to the Torch
in order to adjust the Gas , not provided.
NEW

Blow Hose Valve Assembly w/ 20 Feet of Silicone
Hose and 90 degree Barb Mouth piece. - $90.00

Either 1/4" or 3/8" - Hose and Assembly

Air flows out the direction that the handle is facing , if
handle is centered , both sides are pressured equally.
Bracket provided for mounting to your Lathe.


Buy Separately -

Blow Hose Valve Assembly Only - $60.00

1/4" ID Silicone Blow Hose - $1.70 Foot
3/8" ID Silicone Blow Hose - $2.00 Foot

Blow Hose will include a 90 Degree Barb Mouth Piece ,
and since the Hose's Inside Diameter is either 1/4" or
3/8" , it will hook up directly to Swivels , No adaptor
required.
Drop Down Adapter - $50.00
Add this to the Torch stand to Drop
the Torch down lower.
Lathe Jig - $55.00
Bridging Device for Lathe.  
Accepts Ground Joint Holder Handle , SS Tube
.
GONG Holders
NOT Included
Silicone BOOTS
Adapter for Swivel - Tool or Glass
Comes with 90
Degree Mouth
Piece , 6 feet
of Silicone
Hose , Adapter
on end for 1/4"
Swivel.
Hose is 1/4"
O
utside
Diameter.
NEW White Silicone Blow Hoses -

1/4" ID Silicone Blow Hose - $1.70 Foot
3/8" ID Silicone Blow Hose - $2.00 Foot
OR - 6 foot of either size for $1
1.00

Blow Hose will include a 90 Degree Barb Mouth Piece , and since the Hose's Inside
Diameter is either 1/4" or 3/8" , it will hook up directly to Swivels , No adaptor required.
NEW - Included a
Shaft + T-slot
Adapter for
Mounting to your
Carriage.
NEW  - Blast Shield Economy Bench
Torch Stand - $200.00
Add a Ball Swivel for $70.00 more
-Can Choose either 6" or 18" Torch
Shaft.
-Please Specify Which Torch when
buying.
-Rail has 15" of in and out travel.
-Can use on Lathe or Bench ,but has
no Pivot on slider box.
We have been proud to carry Jeff's foot switches for years. They are equipped with top-of-the-line
Parker 140PSI Oxygen solenoids and Red Hat 15-20 PSI Gas solenoids. The Line-master Pedal is
rugged and comfortable to use, attaching to the rear of the control unit. The control unit can be located
on the floor or mounted under your bench top, and features all brass internal tubing, marked fittings,
indicator lamps, and terminal strip wiring for trouble-free operation.

This single stage switch is suitable for a two-stage torch such as a GTT Phantom or Mirage.
Single Stage Foot Switch - $375.00
FOOT SWITCHES
We have been proud to carry Jeff's foot switches for years. They are equipped with top-of-the-line Parker
140PSI Oxygen solenoids and Red Hat 15-20 PSI Gas solenoids. The Line-master Double-Pedal is
rugged and comfortable to use, attaching to the rear of the control unit. The control unit can be located
on the floor or mounted under your bench top, and features all brass internal tubing, marked fittings,
indicator lamps, and terminal strip wiring for trouble-free operation.

This two-stage foot switch is suitable for three-stage torches such as the GTT Delta Mag or Cobra.
Double Stage Foot Switch - $685.00
Lathe Foot Switch for Ribbon Burners - $425.00
We have been proud to carry Jeff's foot switches for years. They are equipped with top-of-the-line Parker
140PSI Oxygen solenoids and Red Hat 15-20 PSI Gas solenoids. The Line-master Pedal is rugged and
comfortable to use, attaching to the rear of the control unit. The control unit can be located on the floor or
mounted to your lathe, and features all brass internal tubing, marked fittings, and terminal strip wiring for
trouble-free operation.

This foot switch is specifically designed for hands-free operation of your ribbon burners. One gas line
routed in can be split to two separate blocks with their own valves that can be attached to two ribbon
burners.
Manual Single Stage Foot Switch - $375.00
Made by Blast Shield and Jeff Rogers.

On and Off Only

You can hook up 2 or more of these
together for Double and Triple Stage
Foot Switches.
This Blow Hose is
made by FireKis
t